Parts of PS
index > DC Power > Parts of PS

Emerson PSM-E01 Monitoring Module

editor:admin    date:2014-07-22

Introduction

The PSM-E01 monitoring system consists of the PSM-E01 power control unit (PCU) and the monitoring circuits built in rectifiers. The PCU has inbuilt detection circuit to detect the bus-ground voltage. It also can connect to an insulation relay and a battery detector that outputs the fault information by relay contact.
PSM-E01 monitoring system is designed mainly for cooperating partner to build a small capacity EP system used in 35kV or below substations. With rectifiers, this monitoring system can fulfill intelligent battery management, EP system detection and alarm functions. It can report operating data to a remote monitoring system with Modbus or CDT91 protocols, which enables the EP system to be used in an unattended substation.
Detected Signals
PSM-E01 monitoring system detects the analog signals and digital signals of EP system, and displays them or gives an alarm on the LCD of PSM-E01 PCU.
PSM-E01 Detected analog signals
SN
Name
Quantity
Input range
Display range
Error*
Remark
1
AC voltage
1
0 ~ 2Vac standard signal
0 ~ 500V
 ± 2% rated value
Used with Emerson AC voltage sampling board (AVSB) A14A3S1
2
Bus voltage
1
0 ~ 320Vdc
0 ~ 320V
 ± 0.5% rated value
 
3
Battery string voltage
1
0 ~ 320Vdc
0 ~ 320V
 ± 0.5% rated value
4
Load current
1
0 ~ 75mVdc
0 ~ 1500A
 ± 0.5% rated value
Used with shunt
5
Battery current
1
-75mVdc ~ +75mVdc
-1500A ~ +1500A
 ± 0.5% rated value
6
Battery ambient temperature
1
250uA ~ 330uA current
-15°C ~ +50°C
 ± 2°C
Used with Emerson temperature sensor
7
Positive bus -/ netagtive bus - ground voltage
1
0 ~ 320Vdc
0 ~ 320Vdc
 ± 2% rated value
Should use the inbuilt insulation detection function of PSM-E01 PCU
*: Sampling error of PSM-E01 PCU only excluding the error of transducer or AVSB
 
PSM-E01 Detected digital signals
SN
Name
Status
Features
Remark
1
Output air breaker status
NC
All signals are series connected and input to PCU as one signal
Close: the signal has 12V voltage
Open: the signal has 0V voltage.
NC or NO can be set in PCU
2
Battery fuse status
NC
For detecting battery fuse blown status
3
Insulation relay status
NO
For detecting the insulation status of DC bus through insluation relay
4
AC air breaker trip signal
NC
The status or tripping signal of AC air breaker of EP system
5
Battery cell abnormal signal
NC
Battery string and cell status sent from battery detector
6
SPD fault signal
NC
Class C SPD status of EP system
 
PSM-E01 Output signals
SN
Name
Quantity
Remark
1
Audible alarm signal
1
12Vdc drive voltage. Piezoelectricity ceramic buzzer with 12V voltage is recommended
2
Alarm indicator signal
1
12Vdc drive voltage. Yellow LED indicator is recommended
3
Alarm relay output signal
1
Contact capacity: 220Vdc/300mA, 250Vac/1A. All alarms output through one relay
4
Serial port
2
The PCU has RS232 and RS485 ports, but they cannot be used at the same time. All analog signals and digital signals can be sent to a host through these ports with Modbus or CDT91 protocol
 
PSM-E01 Monitoring system functions
SN
Name
Content
Remark
1
Battery management
According to the preset parameters, manage battery boost charging (BC) & float charging (FC), current-limit charging, temperature compensation and battery capacity test
At most 48 hours of manual BC operating is allowed
2
Battery BC protection
Perform battery BC protection according to the preset auto BC protection time
The manual BC protection time and auto BC protection time are two different parameters. Set them separately
Switch to FC upon system abnormality
 
3
Alarming
Battery shunt disconnection, load shunt disconnection
The shunt is damaged or the cable is disconnected
Battery fuse blown, AC air breaker trip, output air breaker trip, SPD fault, battery cell abnormal
 
Bus insulation deterioration
This alarm indicates that the insulation relay has alarm if the insulation detecting mode is set to “Extn” or that the difference between the positive bus to ground voltage and negative bus to ground voltage exceeds threshold if the mode is set to “Intn”
AC over-/under-voltage, AC input failure alarm (AC voltage <50V)
 
Bus, battery over-/under-voltage alarm
 
Battery charge over current alarm
 
System current imbalance alarm
The difference between load current plus battery current and the output current sum of all rectifiers exceeds threshold
Battery string temperature abnormal alarm
Alarm occurs when the battery temperature exceeds the range of -15ºC ~ 45ºC. Battery temperature compensation will stop
Rectifier protection, fault, communication interruption alarm
 
PCU malfunction
The internal 12V and 5V power supplies of PCU are abnormal
4
Background communication
PCU communicates with the host through RS232/RS485 mode. The protocol is Modbus or CDT91 (settable)
www.emerson-cn-com